f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 1 product specification 10 0 g base - sr10 100m cxp optical transceiver module f tld 10ce1c product features 1 2 - channel full - duplex transceiver module hot pluggable cxp form factor maximum link length of 100m on om3 multimode fiber (mmf) multirate capability: 1 . 06gb /s to 1 0 .5gb/s per channel unretimed c ppi electrical interface requires 3.3v power supply only low power dissipation: < 3.5 w reliable vcsel array technology built - in digital diagnostic functions commercial operating case temperature range: 0oc to 70oc single mpo connector receptacle rohs - 6 compliant (lead - free) applications 1 0 0gbase - sr10 100g ethernet multiple 4g/8g/10g fibre channel finisars ftld 10ce1c cxp transceiver modules are designed for use in up to 1 00 gigabit per second links over multimode fiber. they are compliant with the cxp specification 1 and ieee 802.3ba 100gbase - sr10 and cppi interfaces 2 . the transceiver is rohs - 6 compliant and lead - free per directive 2002/95/ec 3 , and finisar application note an - 2038 4 . for applications up t o 12.5 gb/s per channel please contact finisar. product selection ftld 10ce1c 1 0 : up to 1 0 .5 gb/s per channel e : ethernet - compliant optical interface 1: first generation product c: commercial temperature rate
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 2 i. pin descriptions figure 1 C cxp - complia nt 84 - pin connector
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 3 pin symbol name/description notes a1 gnd ground 1 a2 tx1 p transmitter non - inverted data input a3 tx1 n transmitter inverted data input a4 gnd ground 1 a5 tx3 p transmitter non - inverted data input a6 tx3 n transmitter invert ed data input a7 gnd ground 1 a8 tx5 p transmitter non - inverted data input a9 tx5 n transmitter inverted data input a10 gnd ground 1 a11 tx7 p transmitter non - inverted data input a12 tx7 n transmitter inverted data input a13 gnd ground 1 a 14 tx9 p transmitter non - inverted data input a15 tx9 n transmitter inverted data input a16 gnd ground 1 a17 tx11 p transmitter non - inverted data input a18 tx11 n transmitter inverted data input a19 gnd ground 1 a20 scl 2 - wire serial interface c lock a21 sda 2 - wire serial interface data b1 gnd ground 1 b2 tx0 p transmitter non - inverted data input b3 tx0 n transmitter inverted data input b4 gnd ground 1 b5 tx2 p transmitter non - inverted data input b6 tx2 n transmitter inverted data inp ut b7 gnd ground 1 b8 tx4 p transmitter non - inverted data input b9 tx4 n transmitter inverted data input b10 gnd ground 1 b11 tx6 p transmitter non - inverted data input b12 tx6 n transmitter inverted data input b13 gnd ground 1 b14 tx8 p tra nsmitter non - inverted data input b15 tx8 n transmitter inverted data input b16 gnd ground 1 b17 tx10 p transmitter non - inverted data input b18 tx10 n transmitter inverted data input b19 gnd ground 1 b20 vcc3.3 - tx +3.3 v power supply transmitte r b21 vcc12 - tx + 12.0 v power supply transmitter - not connected 2 c1 gnd ground 1 c2 rx1 p receiver non - inverted data output c3 rx1 n receiver inverted data output c4 gnd ground 1 c5 rx3 p receiver non - inverted data output c6 rx3 n receiver i nverted data output c7 gnd ground 1 c8 rx5 p receiver non - inverted data output c9 rx5 n receiver inverted data output c10 gnd ground 1
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 4 c11 rx7 p receiver non - inverted data output c12 rx7 n receiver inverted data output c13 gnd ground 1 c14 rx9 p receiver non - inverted data output c15 rx9 n receiver inverted data output c16 gnd ground 1 c17 rx11 p receiver non - inverted data output c18 rx11 n receiver inverted data output c19 gnd ground 1 c20 prsnt_l module present c21 int_l/res et_l interrupt / reset d1 gnd ground 1 d2 rx0 p receiver non - inverted data output d3 rx0 n receiver inverted data output d4 gnd ground 1 d5 rx2 p receiver non - inverted data output d6 rx2 n receiver inverted data output d7 gnd ground 1 d8 rx 4 p receiver non - inverted data output d9 rx4 n receiver inverted data output d10 gnd ground 1 d11 rx6 p receiver non - inverted data output d12 rx6 n receiver inverted data output d13 gnd ground 1 d14 rx8 p receiver non - inverted data output d15 rx8 n receiver inverted data output d16 gnd ground 1 d17 rx10 p receiver non - inverted data output d18 rx10 n receiver inverted data output d19 gnd ground 1 d20 vcc3.3 - rx +3.3 v power supply receiver d21 vcc12 - rx + 12.0 v power supply receiver - not connected 2 notes 1. c ircuit g round is in ternally isolated from chassis g round. 2. 12v power supply not required.
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 5 ii. general product c haracteristics parameter value unit notes module form factor cxp number of lanes 1 2 tx and 1 2 rx maximum a ggregate data rate 126 gb /s maximum data rate per lane 10.5 gb /s protocols supported typical applications include 100g ethernet, infiniband, fibre channel, sata/sas3 electrical interface and pin - out 84 - pin edge connector pin - out as defined by the cxp specification optical cable type required multimode ribbon 24 - fiber cable assembly, mpo connector maximum power consumption per end 3 .5 w atts varies with output voltage swing and pre - emphasis settings (see figure 2 ) management interface serial, i 2c - based , 450 khz maximum frequency as defined by the cxp specification data rate specifications symbol min typ max units ref. bit rate per lane br 1000 1 0 500 mb/sec 1 bit error ratio ber 10 - 12 2 link distance on om3 mmf d 100 meters 3 notes : 1. infiniband sdr/ddr/qdr, 1/10 /40/100 gigabit ethern et, 1/2/4/8/10g fibre channel . 2. tested with a prbs 2 31 - 1 test pattern. 3. per 100gbase - sr10 pmd maximum link distance in ieee 802.3.ba. iii. absolute maximum ratings parameter symbol min typ max unit re f. maximum supply voltage vcc 1, vcctx, vccrx - 0.5 3.6 v storage temperature t s - 40 85 c case operating temperature t op 0 70 c relative humidity rh 0 85 % 1 notes : 1. non - condensing.
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 6 iv. electrical characteristics (t op = 0 to 70 c, v cc = 3.3 5 % volts) note: the FTLD10CE1C requires that a cppi - compliant cxp electrical connector be used on the host board in order to guarantee its electrical interface specification . please check with your connector supplier. parameter symbol min typ max unit ref. supply voltage vcc1, vcctx, vccrx 3.15 3.45 v supply current icc 850 1000 ma module total power p 3.5 w 1 link turn - on time transmit turn - on time 2000 ms 2 transmitter (per lane) single ended input voltage tolerance vint - 0.3 4.0 v differential data input swing vin,pp 12 0 1200 mvpp 3 differential input threshold 50 mv ac common mode input voltage tolerance (rms) 15 mv differential input return loss per ieee 802.3ba, section 86 a . 4 .1.1 db 4 j2 jitter tolerance jt2 0.17 ui j9 jitter tolerance jt9 0.29 ui data dependent pulse width shrinkage ddpws 0.07 ui eye mask coordinates {x1, x2 y1, y2} 0.1 1 , 0.31 95, 350 ui mv 5 receiver (per lane) single - ended out put voltage - 0.3 4.0 v differential data output swing vout,pp 0 800 mvpp 6,7 a c common mode out put voltage (rms) 7.5 mv termination mismatch at 1 mhx 5 % differential output return loss per ieee 802.3ba, section 86 a . 4 . 2 .1 db 4 common mo de output return loss per ieee 802.3ba, section 86a.4.2.2 db 4 output transition time, 20% to 80% 28 ps j2 jitter output jo2 0.42 ui j9 jitter output jo9 0.65 ui eye mask coordinates {x1, x2 y1, y2} 0 . 29, 0.5 150 , 425 ui mv 5 power supply ripple tolerance psr 50 mvpp notes : 1. maximum total power value is specified across the full temperature and voltage range. 2. from power - on and end of any fault conditions. 3. after internal ac coupling. self - biasing 1 00 differential input. 4. 10 mhz to 11.1 ghz range 5. hit ratio = 5 x 10e - 5 6. ac coupled with 100 di fferential output impedance. 7. settable in 4 discrete steps via the i2c interface . see figure 2 for vo ut settings.
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 7 power ( mw ) pre - emphasis into 100ohms (mv) 0 125 175 325 vo (mv) 0 1189 317 1645 2197 2305 2617 422 1753 2305 2413 2725 7 39 2041 2557 2701 2962 figure 2 C power dissipation ( mw , typical ) vs. rx output conditions v. optical characteristics (t op = 0 to 70 c, v cc = 3.3 5% volts) param eter symbol min typ max unit ref. transmitter (per lane) signaling speed per lane 10.5 gbd 1 center wavelength 840 860 nm rms spectral width sw 0.65 nm average launch power per lane txp x - 7.6 2.4 dbm transmit oma per lane txoma - 5.6 3.0 dbm 2 difference in power between any two lanes [oma] dp x 4.0 db peak power per lane pp x 4.0 dbm launch power [oma] minus tdp per lane p - tdp - 6.5 dbm tdp per lane tdp 3.5 dbm optical extinction ratio er 3.0 db optical return loss tolerance orl 12 db encircled flux flx > 86% at 19 um < 30% at 4.5 um dbm average launch power of off transmitter, per lane - 30 dbm relative intensity noise rin - 128 db/hz 3 transmitter eye mask definition {x1, x2, x3, y1, y2, y3} 0.23, 0.34 , 0.43, 0.27, 0.35, 0.4 receiver (per lane) signaling speed per lane 10.5 gbd 4 center wavelength 840 860 nm damage threshold dt 3.4 dbm average receive power per lane rxp x - 9.5 2.4 dbm receive power (oma) per lane rxoma 3.0 dbm stressed receiver sensitivity (oma) per lane srs - 5.4 dbm peak power, per lane pp x 4 dbm receiver reflectance rfl - 12 db vertical eye closure penalty, per lane 1.9 db stressed eye j2 jitter, per lane 0.3 ui stressed eye j9 jitter, p er lane 0.47 ui oma of each aggressor lane - 0.4 dbm receiver jitter tolerance [oma], per lane - 5.4 dbm rx jitter tolerance: jitter frequency (75, 5) khz, ui
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 8 and p - p amplitude (375, 1) khz, ui los de - assert los d - 11 dbm los ass ert los a - 14 dbm los hysteresis 1 db notes : 1. transmitter consists of 1 2 lasers operating at a maximum rate of 1 0 .5gb/s each. 2. even if tdp is <0.9db, the oma min must exceed this value. 3. rin is scaled by 10*log (10/4) to maintain snr outside of trans mitter. 4. receiver consists of 1 2 photodetectors operating at a maximum rate of 1 0 .5gb/s each. vi. memory map and control registers compatible with the cxp specification . please see finisar application note an - 2085 for a detailed description . vii. environmental specifications finisar ftld10 c transceiver module s have an operating temperature range from 0c to +70c case temperature. environmental specifications symbol min typ max units ref. case operating temperature t op 0 70 c storage temperature t st o - 40 85 c viii. regulatory compliance finisar ftld10 c transceiver module s are rohs - 6 compliant. copies of certificates are available at finisar corporation upon request. ftld10 c transceiver modules are class 1m laser eye safety compliant per iec 60825 - 1 , which means that they are eye safe under normal unaided viewing conditions. laser radiation may be hazardous if viewed with magnifying optics.
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 9 ix. mechanical specifications the ftld10 c transceiver module mechanical specification s are based on the c xp s pecification. figure 5 C ftld10c mechanical drawing
f tl d 10ce1c product specification C august 2011 f i n i s a r finisar corporation C 3 - aug - 1 1 rev b2 page 10 x. references 1. supplement to infiniband architecture specification, volume 2 , release 1.2.1., annex a6: "120 gb/s 12x small form - factor pluggable (cxp) - interface specifica tion for cables, active cables, & transceivers", september 2009 2. ieee 802.3ba, pmd type 10 0gbase - sr 10 3. directive 2002/95/ec of the european council parliament and of the council, on the restriction of the use of certain hazardous substances in electrical and electronic equipment. january 27, 2003 . 4. application note an - 2038: finisar implementation of rohs compliant transceivers, finisar corporation. 5. application note an - 2085: cxp transceiver eeprom mapping , finisar corporation . xi. for more information finisar corporation 13 89 moffett park drive sunnyvale, ca 94089 - 1133 tel. 1 - 408 - 548 - 1000 fax 1 - 408 - 541 - 6138 sales@finisar.com www.finisar.com
|
